• 2

[技巧轉貼]加速 PDA 與3G 藍芽連線上網之速度

轉載自Brighthand:

Raising hx4700 bluetooth dialup speed to match EDGE/3G/UMTS phones

--------------------------------------------------------------------------------

Here is small tweak I figured out and want to share with you.
It's meant for people that use their ipaq with EDGE/3g/UMTS cellphones to access internet. Basically any phone that is able to connect faster than 115200kbps.

Bluetooth DUN (dialup network) connection speed is limited to 115200 bps (14K/s) in hx4700 settings. However, 3g phone is capable of giving you 384000 bps (40K/s) * edit * actually I have got feedback that on EV-DO network some people now get 80KB/s from their phone to their iPAQ. Obviously, bottleneck is in IPAQ.

It is possible to edit speed of connection by using registry editor, such es Tascal Regedit or Resco Registry editor, etc.

All usual disclaimers apply, you do it at your own risk. I made this tweak on hx4700 running on WM5 with Widcomm stack. While I think that it should work on WM2003, 2003SE too, I cannot guarantee that. Try if you want.

1. Set speed of your connection to be exactly 115200. Later, this will help us to identify bytes we need to patch.

2. Find in registry HKCU\Comm\RasBook\"yourconnectionname"\DevCfg

3. It is a data array with some stuff I do not know much about, however, it contains 3 bytes that define connection speed. For example, 115200 decimal = 01.C2.00 hex, stored backwards in the memory as 00.c2.01

4. So find that sequence. In my case it was in bytes 13,14,15

5. Change value to the one from the list below

256000 bps =3E800 -> 00.e8.03
384000 bps =5DC00 -> 00.dc.05
460800 bps =70800 -> 00.08.07
921600 bps =E1000 -> 00.10.0e

Chosen speed should be faster than speed of cellular connection, to cover some protocol overhead. In case of UMTS (max 384kbps) I have chosen speed of 460800 bps. If you use EDGE, than 256000 should be enough.

6. Now, we switch off 4700 for a minute to let registry values flush into persistent memory.

7. Soft reset. Enjoy higher speeds.

P.S. My machine is stable after this tweak. Speed is 2xFaster now. Download tests gave me consistent 33-38 K/s on my 3g network. However, I do not know how it will behave if you edit connection settings again. I guess it will fall back to old speed setting. I simply do not open it now.


以上個人試過了,確實有效,配合遠傳 3G上網,快多了
分享給大家
2006-04-23 11:49 發佈
老大!英文不好勒
可以簡單的翻成中文嗎感謝
真的有效
我使用n300+VIBO
本來的連線看年代新聞只聽的到聲音
修改了之後影像可以順利看到了(會LAG)
大隻佬 wrote:
老大!英文不好勒可以...(恕刪)


有效啦!尤其有在看網路電視的。
簡短說明

2. Find in registry HKCU\Comm\RasBook\"yourconnectionname"\DevCfg

反正先找到RasBook這項機碼,底下會根據連線速度有115200或速度更少的資料,裡頭每個都有DevCfg這個機碼
一般設定3G連線,用原先PDA內的藍芽modem最大速度頂多115200,作者要你去改這項DevCfg值,但是我之前就設好連線,用的是威寶連線名稱也設vibo,裡頭就多一項vibo,我就直接改它的DevCfg值(如果失敗頂多刪除連線重新設定)
接下來進入數位密碼,反正大家也不是科班出身的,就是找到00.c2.01這三碼相連的準備修改。
針對速度可以改
256000 bps =3E800 -> 00.e8.03
384000 bps =5DC00 -> 00.dc.05
460800 bps =70800 -> 00.08.07
921600 bps =E1000 -> 00.10.0e

因為目前3G理論384000 bps就改成00.dc.05

試試看囉
請問一下,要改那裏?
我是使用dopod900,中華電信3G上網
為何我找不到00.c2.01這串呢?
kevinclp1 wrote:
請問一下,要改那裏?...(恕刪)


我也找不到!dopod 900

我愛PDA
PDA 透過藍芽與 3G手機連線上網才有需要

Dopod 900 不必透過藍芽,直接上網就可以啦,不需修改
真的有效!我的4150搭z800i改過後,從本來頓頓的上網速度提升到還可以接受,跟wLAN相差無幾的程度!

太感謝了!
改到384000 bps後到中華電信測速網頁測試
連線速度最高只有到280k bps
一度以為是威寶3G上網最快速度了
與威寶客服詢問了多次,大都被認為是正常
說因為"無線"傳輸的影響因素很多
但是威寶網站上有說明3G連線實際速度在 160k ~ 320k bps 之間
所以只能跑到280k bps真是無法接受(好像機車無法破百的痛苦)
後來想到PDA藍芽連線速度還有增加的空間
就一口氣改到921600 bps
再到測速網頁測速,竟然...
看到連線速度破300k bps了
最快有到328k bps,符合威寶官方公佈的最高速度
讓我對威寶的3G上網卡有信心了些(都簽約兩年了)
希望威寶能繼續加油,甚至能超越中華電信
讓消費者能有更好的無線通訊服務可選擇
想這樣沒煩憂唱著歌一直走
是每台PDA都可以做這類更改嗎?
小弟在我的Mio A201找不到此類選項。
真希望可以增加藍芽和PDA的連線速度...
  • 2
內文搜尋
X
評分
評分
複製連結
Mobile01提醒您
您目前瀏覽的是行動版網頁
是否切換到電腦版網頁呢?