Nelson0630 wrote:
期待更多功能，不知...(恕刪)
用5053 VCDS解影音限速目前爬文好像還沒看過
大部份都是用OBDELEVEN去解最快最省事
1.Access 9. Central Elec.
2.通關密碼：31347
3.Adaptation
4.選擇通道：ENG10577-ENG116587-Au絽nlicht_Blinker-Komfortblinken Blinkzyklen
5.輸入想要的閃爍次數（1～5次），Do it!
6.Go Back
7.接下來的步驟最重要：進入MIB II主機CAR選項裡的「設定」，重置「照明」至原廠設定，新設定才會生效
踩煞車時，使尾門的燈也會一併亮起：
1.Access 9. Central Elec.
2.通關密碼：31347
3.Adaptation
4.選擇通道：Leuchte23SL HLC10-Lichtfunktion C 23
5.設為Brake Light（這是左邊的），Do It！
6.選擇通道：Leuchte23SL HLC10-Dimmwert CD 23
7.將0改為100（已經是最亮的了，不要設127），Do It！
8.選擇通道：Leuchte24SL HRA65-Lichtfunktion C 24
9.設為Brake Light（這是右邊的），Do It！
10.選擇通道：Leuchte24SL HRA-Dimmwert CD 24
11.將0改為100，Do It！
********************************************************
若只完成以上步驟，因為尾門板本來只擔負尾燈的工作，所以燈泡僅為T10 5W，在白天發揮煞車燈的亮度等於尾燈的亮度，和車身的燈組亮度會不一樣。所以建議更換成T15 16W（有些是18W）（左右共4顆），再來
12.選擇通道：Leuchte23SL HLC10-Dimmwert AB 23
13.將94改為30，Do It！
14.選擇通道：Leuchte24SL HRA-Dimmwert AB 24
15.將94改為30，Do It！
16.Go Back
09-Central Electronics
16-Security code 31347
10- Adaptation
(6) Leuchte8FL LB2-Dimmwert AB 8 (left headlight)
CHANGE VALUE FROM 127 to 0.
(6) Leuchte9FL RB2-Dimmwert AB 9 (right headlight)
CHANGE VALUE FROM 127 to 0.
Disable Seatbelt Warning
17 Instruments
Adaptation Channels -> function 10
Select disable seatbelt warning
change to "yes" (default: none).
Disable the annoying tone when the ignition and driver's door open.
17 Instruments
Adaptations
Ignition active message; Trigger
Change to "No display" (default value: driver's door)
German translation for this is.....
German translation…..
STG 17 (Schalttafeleinsatz) auswählen
STG Anpassung -> Funktion 10
Zündung aktiv Meldung; Auslöser
ändern auf "Keine Anzeige"
Change comfort blinking
Adaptation channels in the central electronics module - (2) - Turn Signal Controls. Default is 3, add can be set as high as 5 flashes. After this, go into Car Menu >setup>factory settings>Lights. Reset the light setting to factory and then it will work
Rain closing windows
Go to [09] Central Electronics
Go to Secuity Access and enter 31347
Go to adaptation channels and set the following:
- (15) Access Control 2 - Regenschliessen_ein aus (Rain Closing on / off) - Select Active
- (16) Access Control 2 - Regenschliessen_art (Rain closing Type) set to Permanent
- (28) Access Control 2 - Menuesteuerung Regenschliessen (Menu Control Rain close) – Set to Active (enables the menu in the ifotainment screen)
THEN
9 Central Electronics
Rain and light sensor
Byte 0…Enable Bit 2 “Regenschliessen aktiv”. (rain closing active)
Bit 1 should be active too….Regenlicht aktiv (rain light active)
My Old coding…..00A8DD
My New coding….06A8DD
Comfort Close windows
Step by step pics here......
https://drive.google.com/file/d/0BzB...ZHN2VRWEU/view
9- Central electronics
10- Adaptations
2-Access control 2- comfort opening > active
3- access control 3- comfort closing > active
Key fob…
7- access control 2- funk komfort oeffnen > active
6- access control 2- funk komfort schilessen > active
Menu
27 access control 2- Menuesteuerung komfortbedienung einstellbar >adjustableKessy
20- access control 2-Kessy komfort schilessen > active
Automatic Air Recirculation....this places the option in the AC setting on the nav screen.
08 Auto HVAC
Long coding
Byte 4
Bit 4-5 use drop down box and select “10 Recirculation Air settings (after ignition cycle) stored.
Sound actuator
Go to A9 Struct. Borne Sound
Adaptation 10
Select "Channel of structure borne sound actuator" (only one)
Std value 100% Change to the value you want, stored in %
Passenger mirror dip…mirror switch has to be on the passenger setting for it to work.
52 Passenger door
07 coding
Byte 4
Enable bit 2 and 3
THEN
09 Central Electronics
31347
Adaptations
17-Access control 2 Spiegelabsenkung bei Rueckwaertsfahrt (change to “active”)
THEN
(22) Access control 2-Menuesteuerung Spiegelabsenkung (change to “active”) this puts
the option in the menu screen.
To adjust your fuel tank calibration to match your reciept..
17-Instruments
16-Security code 20103
10-Adaptations
(1) Offset for tank calibration values - Offset sensor 1: from -12.8l to +2l
Range is -12.8 to +8.
-12.8l is the factory default.
<0 moves the needle down.
=0 no change/movement
>0 move needle up.
+1 = needle moves up by ~1/16 up
+2 = needle moves up by ~1/8 up
Password to unlock [09] Central Electronics Menus
Go into Function 16 (Permissions)
Enter the code 31347
Disable Seatbelt Warning
Go into [17] Instruments
Adaptation Channels -> function 10
Select disable seatbelt warning (Gurtwarner deaktivieren)
change to "yes" (default: none)
Setting Fog Lights as Coming/Leaving Home
Go into [09] Central Electronics
Go into Security Access and enter 31347
Look for the German text under "Comfort-Illumination"
Set the new value drop down to "Fog Light"
Display the battery charge level or SOC (state of Charge)
Enter [17] Instruments
Go to adaptation channels, (no need for a security log in with this module)
Scroll down until you see Battery Charge > simply change it in the new value drop down to "active" and it's done.
Automatic rain closing
Go into [09] Central Electronics
Go into Secuity Access and enter 31347
Go to adaptation channels and set the following:
- (15) Access Control 2 - Regenschliessen_ein aus (Rain Closing on / off) - Select Active
- (16) Access Control 2 - Regenschliessen_art (Rain closing Type) set to Permanent
- (28) Access Control 2 - Menuesteuerung Regenschliessen (Menu Control Rain close) – Set to Active (enables the menu in the ifotainment screen)
Alarm beep on lock / unlock
Go into [09] Central Electronics
Go into Secuity Access and enter 31347
Adaptation channels, and you are looking for:
(1)-Acknowledgement Signals -Akustische Rueckmeldung entriegen (un-lock acoustic feedback)
(2)-Acknowledgement Signals -Akustische Rueckmeldung verriegeln (lock acoustic feedback)
Set one or both to on if you wish.
Then set the following to "on"
Gauge sweep
Go into [17] Instrument
Coding -> Function 10
Byte 1
Enable bit 0
Disable the little red led's on the side of the taillights
09-Central Electronics
16-Security code 31347
10-Adaptations
(1)-Leuchte27NSL RC6-Lasttyp 27 to not active
Change instruments to Carbon Fiber look
17 Instruments
STG adjustment > function 10
Select “channel display representation” (displaydarstellung)
Change to “Version 2” (default is version 1)
Amount of fuel (in Gallons) used since the last fill up (refuel quantity)
17 Instruments
Long Coding
Go to Byte 10
Enable bit 4
內文搜尋
從 APP 打開
X