LG Optimus 2X 超頻工具 大家都用什麼?

不知道大家在裝了超頻內核之後, 都用哪套超頻工具?

目前用過的有
1. SetCPU ==> 要支援到1G以上, 要手動建立setcpu.txt 放到/sdcard/下面
2. pimpmycpu ==> 沒有widget可以顯示現在到底跑多快, idle是否會降頻
3. 超級兔子CPU超頻大師免費版 ==> 不支援情境模式, 有widget可以顯示CPU Speed,

現在主要用超級兔子CPU超頻大師, 降頻最低可到216MHz, 但是216MHz放久了會不開機, 要拔電池

設到300MHz就很正常, 待機很省電

LG Optimus 2X  超頻工具 大家都用什麼?

=====================================================================================
現在改用setcpu 2.1.2.1付費版 + setcpu.txt
有情境模式
widget 也能show current speed
2011-04-25 14:39 發佈
我是用pimpcpu,超頻最高是到1.2GHz,平時待機是300MHz,真的在待機下超省電,在3g開著和背景同步開著的狀況下(關gps跟wifi),目前待機兩天了,電力還有42%,當中有講了大概半小時電話外加半小時的上網!!

miswu wrote:
我是用pimpcpu...(恕刪)


我也是用pimpcpu,超到1.4GHz,沒有勾選待機時降頻...
大大有沒有發現,勾選了待機時降頻到最低,當關屏後再按開關鍵,要等一下子螢幕才會亮嗎?也許我比較心急吧...現在沒有勾選待機降頻,一按就亮了,感覺比較爽...
我是用1.4版的,最高超到1.2,最低是300MHz,你提的問題,我倒是沒有這樣@@

maumaumiow wrote:
不知道大家在裝了超頻...(恕刪)


我是用:超級兔子CPU超頻大師免費版

500~ 1200還不錯用,只是醒來比較慢......

感恩宇宙,感恩未來! 感恩宇宙,感恩愛! 感恩宇宙,感恩愛! 感恩宇宙,感恩一切有了交代!

wll99979 wrote:
我是用:超級兔子CP...(恕刪)


因為用的到情境模式..
所以一時衝動下購買了正版..
結果授權2小時還沒授權過關-.-
反而是先被信用卡扣款1台幣...
不去國揚、漢神、漢來集團消費,是我消費經驗的堅持
我用 setcpu
情境模式
平常 216~1000
充電 912~1000
關瑩目時 216~312

快樂使用中
maumaumiow wrote:
不知道大家在裝了超頻...(恕刪)


請問手動建立setcpu.txt 是什麼意思呢? txt裡面要打什麼指令嗎

如果不刷機 只有root有辦法超頻嗎
8. Custom Frequency Config
In rare situations and in older kernels, and when SetCPU cannot get root access, SetCPU may not be able to autodetect the full range of speeds supported by the kernel. If this is the case, you can configure SetCPU to use custom frequencies. To get started, you'll need the list of frequencies your kernel can support in kHz (not MHz!).
Create a plain text file called 「setcpu.txt」 and place it on the root directory of your SD card or on your SD card's ext partition (/sdcard/ or /system/sd/). The text files should sort the frequencies on one line by comma, from lowest to highest. For example, the following is a valid config file:
125000,250000,500000,550000,600000
To store the custom frequency list on your phone, save it as 「setcpu」 with no extension and put it in /data/. SetCPU reads from the SD card first and uses that text file if present, then tries to read from /data/.
To configure SetCPU to read your custom frequencies, go back to the device selection screen (in the Main tab, press Menu > Device Selection), choose 「show other frequencies」 if necessary, and choose the custom config option at the very bottom.

※警告:超頻會導致系統不穩定,請小心超頻,超壞自行負責。※

不刷機也可以

簡單的作法
1.root過,安裝setcpu
2.在電腦上用記事本,把你想要的頻率寫好,如1024000就是1024也就是1G,上面原文的範例是從125~600。
3.把這個檔案存到/sdcard/ or /system/sd/ 皆可
4.打開SETCPU
5.按下MENU鍵,然後選擇「Device Selecion」後,再選擇「show other frequencies」,他就會讀你設定的setcpu

※警告:超頻會導致系統不穩定,請小心超頻,超壞自行負責。※
內文搜尋
X
評分
評分
複製連結
Mobile01提醒您
您目前瀏覽的是行動版網頁
是否切換到電腦版網頁呢?