請問關於g 系列的7速變速箱

Paat
個人積分：207分
文章編號：39963549

207分

樓主

2012-11-21 2:05

請問關於g37的變速箱..小弟總覺得他設計怪怪的.
以下以自檔且未拉高時速的情形下
前三段在時速2x前就會換了.. (因此會覺得起步不是很輕快...)
到時速75左右到第七速... (高速反而油門超輕..xd!!! )
小弟之前的車是5速手自排.
大概也是時速近70的時候換到第五速....
一直覺得是小g 是為了平衡市區油耗...所以這樣設定的..
但是前幾天聽到朋友說他的jaguar 第8速很少用到. 因為要達到時速100以上才會換..-.-.....
那...小g的七速設定怎麼會這樣.....

2012-11-21 2:05 發佈

文章關鍵字 G 系列變速箱

yypups

yypups
個人積分：17分
文章編號：39964026

17分

2樓

2012-11-21 3:45

恩...

調成手排... 想什麼時候換檔, 就什麼時候換檔囉~~~

話說... 有聽過傳說, 車子也可以訓練的...

如果真的覺得很不順, 砍掉重練試試看~~

有一次出差回來, 不知道是心理作用還是真的被我老婆練到走位...

重練以後... 順很多了...

(雖然我現在沒事還是會玩手排... 不過自排已經算很好開了)

喔... 我不是開 G, 我開 FX...

Paat

Paat
個人積分：207分
文章編號：39971713

207分

樓主

2012-11-21 13:10

@@ 可以這樣??? 請問如何砍掉重練呢??(重新設定?)

yypups

yypups
個人積分：17分
文章編號：39976242

17分

4樓

2012-11-21 16:27

本來要睡了... (凌晨 12:11)
(加拿大有時差 >_<)

不過看到... 先回一下再睡好了...
(車友的事情, 比較重要 ~^^~)

基本上, G 跟 FX 應該都是一樣的重設法吧...
(說明書也有寫)

有很多東西可以重設 (砍掉重練)

基本上, 重設 ECU 應該就會讓你很有 FU 了...

以下... 是以前有人整理好, 我抓下來的....

ECU Resetting Procedures

Timing is extremely critical. If it is NOT DONE within the specify time, the ECU will not reset and the Check Engine Light (CEL) will continue to remain ON.
A stop watch or an analog clock with a second?s needle will be useful.

Operations Procedures

1. Confirm that accelerator pedal is fully released, turn ignition switch ?ON? and wait 3 seconds.
2. Repeat the following steps (2a and 2b) procedures quickly five times within 5 seconds.
2a. Fully depress the accelerator pedal (HARD).
2b. Fully release the accelerator pedal.
3. Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 10 seconds until the CEL starts blinking.
4. Fully release the accelerator pedal (while the CEL is still blinking)
5. Wait about 10 second.
6. Fully depress the accelerator pedal and keep it for more than 10 seconds.
7. Fully release the accelerator pedal (The CEL light will continue to blink).
8. Turn ignition switch to ?OFF? position and now you can start the car. The CEL light should be gone.

If the CEL light continues to remain ON, repeat the above steps. Timing is EXTREMELY critical to resetting the ECU.

Accelerator Pedal Release Position Learning

Operation Procedure
1. Make sure that the accelerator pedal is fully released.
2. Turn ignition switch ?ON? and wait at least 2 seconds.
3. Turn ignition switch ?OFF? wait at least 10 seconds.
4. Turn ignition switch ?ON? and wait at least 2 seconds.
5. Turn ignition switch ?OFF? wait at least 10 seconds.

Throttle Valve Closed Position Learning

Operation Procedures
1. Make sure that accelerator pedal is fully released.
2. Turn ignition switch is ?ON?.
3. Turn ignition switch is ?OFF? wait at least 10 seconds.
Make sure that the throttle valve moves during above 10 seconds by confirming the operating sound.

Idle Air Volume Learning (Throttle Position Learning)
It is better to count the time accurately with a clock.

Operation Procedures
1. Perform ?Accelerator Pedal Released Position Learning?.
2. Perform ?Throttle Valve Closed Position Learning?.
3. Start engine and warm it up to normal operating temperature.
4. Turn ignition switch ?OFF? and wait at least 10 seconds.
5. Conform that accelerator pedal is fully released, turn ignition switch ?ON? and wait 3 seconds.
6. Repeat the following (steps 7a, 7b) procedures quickly five times within 5 seconds.
7a. Fully depress the accelerator pedal (HARD)
7b. Fully release the accelerator pedal.
8. Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 20 seconds until the Check Engine Light (CEL) stops blinking and turned ON.
9. Fully release the accelerator pedal within 3 seconds after the CEL is ON.
10. Start engine and let it idle.
11. Wait 20 seconds.
12. Rev up the engine two or three times and make sure the idle speed and ignition timing are within the specifications.

*You have to do the accelerator position learning sequence first!*

如果覺得太麻煩.... 那直接斷汽車電池吧....
那也可以清除 ECU 設定的...

只不過... 副作用是...
所有的電子設定也會跟著消失...
(例如... 座位設定, 收音機電台設定, 有的沒有的)
(不過也有人說那樣沒用... 雖然大部分的人都說有用...)

我"個人"是覺得有差~~~

以下是補強... (應該跟上面的大同小異, 只是不同的形容方式)

ECU Accelerator Pedal Reset Proc
Note: Timing is critical for this to work!
1. Turn the ignition switch to on. Dash gauges lit. Don’t start the engine!
2. Wait 3 seconds.
3. Fully depress and release the accelerator pedal 5 times within 5 seconds.
4. Wait 7 to 10 seconds.
5. Fully depress the accelerator pedal for ap
indicating Diagnostic Test Mode II (Self-diagnostic results) has started.
6. Release accelerator pedal and wait 5 to 10 seconds.
7. Fully depress the accelerator pedal for 10 seconds. At this point the check engine light should change to blinking slowly
indicating “Erasing ECU Memory”.
8. Release the accelerator pedal and turn the ignition switch to off.
9. Restart the engine. The check engine l
Note: If the check engine light doesn't blink as described in steps 5 & & 7, then the ECU isn't reset.
* If above didn't work, disconnect the battery negative and pump the brake t
foolproof as long as all ECU control parameters are within their normal ranges

以上... 不負責任的交代/步驟...

晚安~~~
(>_< 00:26 分了, 我明天 5:30 還要起床... 慘了.. 大約只剩 5 個小時可以睡了)

Paat

Paat
個人積分：207分
文章編號：39988770

207分

樓主

2012-11-22 2:37

感謝大大的詳細回復~~^^感激您

rex0926

rex0926
個人積分：12分
文章編號：39993858

12分

6樓

2012-11-22 10:55

Paat wrote:
請問關於g37的變速...(恕刪)

ECU Reset重置歸零
(CEL燈在舊蛙及舊G應該是Service Engine Soon的黃色燈號, 新蛙是一個黃色圖示MIL燈號~故障指示燈)
1. 將點火開關轉到“ON”位置 (不可發動引擎 ); 接著默數3秒.......1秒, 2秒, 3秒
2. 第4~8秒: 一秒一次完全踩放油門踏板, 共5次循環(一踩一放為一次循環, 踩要到底,放要全放) ,一定要在5秒內完成!
3. 第15~16秒, 踩住油門到底; 大約第20秒時此時SES燈開始連續閃爍, 速度較慢
4. 第30秒, 全放鬆油門
5. 第40秒, 踩住油門到底 ; 這裡開使燈號閃爍速度加快, 以快速閃爍10次為一循環,總共有3個循環
6. 接續步驟5, 仍然踩住油門, 等待燈號快閃3個循環完成後, 燈號會轉為較慢的閃爍, 閃個3~5次即可鬆開油門
7. 放鬆油門後,隨即將點火開關轉到“OFF”位置, 再啟動引擎! 完成!

或是你可跟著影片做!
http://www.youtube.com/watch?feature=player_embedded&v=95WszTnphPI

svmaxstyle

svmaxstyle
個人積分：108分
文章編號：40032481

108分

7樓

2012-11-23 18:34

rex0926 wrote:
ECU Reset重...(恕刪)

哇賽~密技~

http://www.wretch.cc/album/svmaxstyle

qk8888

qk8888
個人積分：81分
文章編號：40032604

81分

8樓

2012-11-23 18:42

好像在打電動輸入密技一樣
換個方式開車電腦不會再次學習嗎?