Dear Sir.
At night, There are some restrictions on recognizing the object like license plate number over exposure
because of the low performance of CMOS sensor in low light environments.
and CR-200HD, It cannot support the Full-HD 30 frames. Only it supports Full-HD 15fps and HD 30fps.
Please find attached file of the CR-200HD quick guide preliminary version.
We are sorry that it is preliminary version and not revised for the latest firmware 2.01.102 yet.
We are sorry that we can’t let you get user manual yet.
We are hoping that the User manual in English version will end around the end of April, 2011.
And also Please find attached file of the CR-200HD new firmware, 2.01.102, English version.
The latest firmware version is 2.01.102.
please update the firmware of CR-200HD as described below.
Firmware update procedure CR-200HD
1. Please draw out the SD-card from CR200HD
2. Please format the SD-card ( FAT32 )
3. Please unzip the attatched ZIP file. It result in 4 files below.
4. Please copy the attached 2.01.102 firmware ( 4 files ) into your SD-card from your desk-top.or lap-top.
5. After finishing to copy the 4 files to your SD-card, Insert the SD-card into CR-200HD
6. Please connect the PC to CR-200HD with USB cable
7. Automatically Updating : LED Blinking about 1 minutes ( O : Yellow / ∇ : white blinking )
8. Finished the Updating : ding-dong alarm + audio ment “Video recording starts”
9. after the audio alarm, it works automatically normal video recording operation. ( O : Green / ∇ : Blue )
Concerning the English version, 2.01.102, It include new configuration program, alarm voice in English.
Procedure to Configure the CR-200HD.
You can set some parameters with configuration program in CR-200HD.
1. If you connect the CR-200HD with your Desk-top or Lap-top with USB cable ,
2. It automatically starts after booting procedure about 30 seconds.
3. After booting, the LED in button turns into ( O : Green / ∇ : Blue ) state.
4. At that time if you push the blue ∇ button for 2 seconds,
5. It changed into USB Mode with “USB mode” voice alarm. And you can see the new Mass storage device like below in Your desk-top.
6. If you double click “CR-200HD_Config.exe “ You can see the Configuration program.
7. Please configure the parameters, and press the OK button.
1920X1080 每秒30張的功能應該是無解...
給我這英文.對了.新的韌體:
[펌웨어 업그레이드] 블랙박스 CR-200HD (Firmware Ver. 2.01.002 )
而2.01.102應該是英文版本的....
AAPL wrote:
嗯...這種情況我遇...(恕刪)
剛剛客服的回覆:
Dear Sir.
1. I think that It is because that May be the vibration of your CAR was so small even if the engine was ON.
If the vibration of the CAR was small when being parked and the power was still ON, that is, the value of output of the 3-axis accelerometer in the CR-200HD is smaller than the threshold value to decide whether it is being parked or not, for 10 minutes
It can be considered that the CAR was parked, and thenCR-200HD was changed into Parking mode.
2. When into the Parking mode, It can record the parking event of some impact from car or human outside and can record the motion event of the objects in the view angle of the CR-200HD. It could be recorded only when the Power was still ON as I mentioned in the former mail .
3. If the car is moving again and the average value of output of the 3-axis accelerometer in the CR-200HD is larger than the threshold value to decide the normal driving status during 10 seconds, CR-200HD will be changed into the normal driving recording mode automatically.
Typically if you start to drive, it might be changed into the Normal driving state and resume recording automatically in 10 seconds or so.
CR-200HD only decide the driving mode or parking mode with the output of the 3-axis accelerometer in it, not with switching into “P” in your Car.
Sincerely
大概意思是說:就是根據3軸加速感應器的敏感度來決定你是否是停車狀態,車停10分鐘後會自動切換成停車模式
若車子恢復行進中大概10秒就會自動切換成即時錄影
我只能說,原來我們國貨跟人家差別在這裡,並不是哈韓....用心程度吧
害我還誤會人家是當機
內文搜尋
從 APP 打開
X