lumix14-50變14-22

今天鏡頭變交環禿然卡住

轉到22左右就無法動了 請問各位有類似的經驗嗎

送修大概要多少時間多少錢

鏡頭壞了心情好差阿 而且人在巴黎暑假才會回台灣

怕危修時間太久 等我要回巴黎的時候還沒修好
2010-06-22 18:40 發佈
vino172 wrote:
http://www...(恕刪)

謝謝妳的回復
看來在我回巴黎之前是不會修好了 好難過
y73327 wrote:
謝謝妳的回復看來在我...(恕刪)



还有一个办法是自己解决. 网上有人贴出了修理这个问题的教程. 只需10分数, 不少人都报告说成功修复了. 具体步骤如下 (e文的, 不好意思):

*remove the rubber (front) ring

*remove the two metal stripes carefully

*remove the screws which are direct in sight

*now you can pull the front ring backwards carefully

*you can see three screw more insight the lens. in my case, all these screws were loose

*tighten the three screws and assemble the lens in opposite way

Be careful not to bend the metal stripes to much, otherwise the won't fit fine.

其他几个人的经验体会:

Just to recap:

Whip off rubber grip. This reveals two metal strips.

Whip off strips. This reveals three conventional screws that form stops and two long non-standard screws that connect the inner ring to the outer.

Remove all five fasteners and the zoom ring will now rotate without zooming.

Rotate the ring and find three more screws internally. If one of these became loose it would undoubtedly jam then lens, just as the lens is jammed now.


另两个人的:

Though I would like to add a couple of details.

The metal strips are glued in place, but sliding a screwdriver underneath should do the job.

In addition, at least on my VARIO-ELMARIT, one of the three screws to be tightened was partially obstructed by one of the lens-posts. By carefully inserting a suitable micro-phillips screwdriver at an angle it was possible to tighten it sufficiently. Remember to add a drop of Lock-tite!
thanks again.

Thanks for the repair instructions! It took a little bit of fiddling to get the metal strips back in place properly, but the rubber ring held it all tight. Works good as new.

无忌网上也有一个同学成功修复了. 这是他的经验: "是这样的,橡胶环没什么好说的.拿下来之后,先是2个长螺丝.(我建议松掉之前,先想办法转到50.不然最后会找不到最后的螺丝).

然后是两个金属条,这个是用双面胶贴上去了.拿下来之后可能会失去粘性,我后来在反面重贴了新的双面胶

金属条拿下之后,有3个小螺丝.这个螺丝下面有个金属圈.要记得一起拿下来.不然容易丢.

松掉之后,可以把那个塑料环往上移了.在根部会有3个螺丝.其中2个比较好旋.有一个很难操作.正好卡在一块塑料后面,我正是这个松了..花了一翻力气才搞定

然后再装起来就行了.主要是金属条粘性失去后比较麻烦,我用了新的双面胶也有点松.最后把橡胶条绑上,也就可以了.

没什么特别要注意的.只要不把拆下来的螺丝弄丢,别的基本都没有危险性."
blackschiele wrote:
还有一个办法是自己解...(恕刪)

謝謝妳的經驗分享

但我有個疑問 您說鬆開2個螺絲前要先轉到50

但我現在只能轉到22左右耶

所以基本上就是鬆開從裝就可以恢復正常嗎 裡面的機構都不用換?
y73327 wrote:
謝謝妳的經驗分享但我...(恕刪)


我没有亲自拆过, 所以具体步骤不是非常清楚. 但修理过程不需要换然后零件, 因为镜头变焦卡住的原因是里面3个螺丝松了, 解决的方法就是把它们拧紧就好了.
內文搜尋
X
評分
評分
複製連結
Mobile01提醒您
您目前瀏覽的是行動版網頁
是否切換到電腦版網頁呢?