http://h18007.www1.hp.com/support/files/HandheldiPAQ/us/download/22776.html
Family models
HP iPAQ hx2700 Pocket PC Series All Models
HP iPAQ hx2400 Pocket PC Series All Models
HP iPAQ hx2100 Pocket PC Series All Models
Important Note!
IMPORTANT:
The RUU is designed to replace the current ROM image and to erase the partnership and all user data and programs on the handheld. It is important to read and understand the information in the Readme file that is included with this update BEFORE installing the package.
Fixes
Fixes issue with CompactFlash (CF) Modem connection and dropped connections.
Fixes issue where CF slot continuously powers the GSM/GPRS CF Card.
Fixes some instances of the issue indicated by the "BTTracyCE.exe" error message.
Fixes corruption issue that may occur with the transmission of Infrared Data Association (IrDA) data in "raw" mode.
Fixes issue where certain characters are not recognized when HP ProtectTools is activated.
Fixes issue where Secure Digital Input/Output (SDIO) cards may not be recognized or may drop the connection.
Fixes intermittent issue where handheld will not Power On and requires a soft reset.
Fixes issues with wireless connectivity.
Fixes issue with WLAN connection where handheld will not connect if the WPA key management or Cisco CCKM key management is enabled and set to "optional."
Fixes issue where handheld stops responding when using a third-party audio application.
Fixes issue where the user interface for the handheld would indicate that the user was connected to a network that was not present.
Fixes issue where protected extensible authentication protocol (PEAP) authentication would fail with no indication that the user's password had expired.
Fixes issue where Pocket Internet Explorer would stall and fail to load a page if the HTTP post was larger than 16K.
Fixes issue where WiFi connection status was incorrectly indicated for some conditions.
Fixes issue with an active modem connection where the handheld was unable to re-establish a connection after the USB cable was unplugged.
Fixes issue that occurred when using WPA-PSK authentication where the handheld failed to authenticate to a second access point (AP) with the same SSID and key.
Fixes issue where the client device packets did not properly route to the target LAN when a point-to-point protocol (PPP) connection was made.
Fixes issue where an exception was generated When disconnecting a serial line Internet protocol (SLIP) server session.
Fixes issue where the wrong domain name server (DNS) address was passed to the server when a secondary IP address was assigned.
Fixes issue where the wrong WEP key was used when switching between configured, preferred, WEP-enabled Wi-Fi connections.
Fixes issue with cached pages where a back/forward navigation would not be sent to the Internet.
Fixes issue with URLs that contain semicolons so that they are no longer truncated when sending the GET request over the Wireless Session Protocol.
Fixes the following localization issues:
Korean: Fixes issue with contact picker where it did not match Jungseong because asterisk (*) and pound sign (#) key presses were ignored.
Korean: Fixes issue with contact names that were displayed with no comma or space between the Last and First name.
Korean: Fixes issue with the Notification dialog so it is no longer clipped in the Sounds and Notifications Control panel.
Romanian: Corrects Daylight Savings Time.
hsj202081 wrote:
我的pda是hp2410，因為是新手英文又爛，請問如何檢查自已的版本是新或舊?要如何更新?更新有何作用?哪位大大可否告知?謝謝!
HP機子更新ROM的方法應該是類似的
提供這篇給您參考
希望對您有幫助
http://www.mobile01.com/topicdetail.php?f=61&t=85637&last=605227
ouyang wrote:
我的是hx2410，
有HP Protect-tools這個程式，
不知你遇到的是啥問題?
我可以幫忙測試看看Evolution wrote:
我的hx2750已經更新了，問題是有比較少了不過是乎某些問題還是存在著。
想請問一下使用Hx2410的朋友，hx2410是否有HP Protect-tools這個程式，因為我的2750更新後這部份會導致的問題還是存在想要確認一下。
就是設定了HP安全性後，藍牙開啟還是會有問題，這在有只紋辨識系統的hx2750上有點可憐，
在hx2410上應該是變成只能設定密碼的方式來鎖定吧？
1.我測試後發現不管有沒有使用指紋辨識只要啟動這個安全性後，就會無法開啟藍牙還是一樣出現那個BTTrayCE的ERRO，只使用PIN碼也這樣。另外我發現這個跟SD卡有關係，如果有啟動HP安全性然後不插SD卡藍牙就可以開啟。
2.還有一個狀況是啟用HP安全性後有啟動指紋辨識的功能，此時開啟藍牙後關機在開啟後，出現要刷指紋的畫面然後就跳出一個錯誤訊息HP protect Tools發生內部錯誤(-100)，之後就非得softrest不可了。
3.啟動藍牙後通常是藍芽已經跟某樣東西連線後，在啟動wifi會出現無法辨識卡的網路卡的訊息，接著wifi就無法開啟了，必須先把藍芽關閉後wifi才能在開，有時會必須softreset後才能在開wifi。
內文搜尋
從 APP 打開
X