jake8187 wrote:
已買近1各月 汽泡機...(恕刪)
大大,自己打氣太危險了啦，我問過朋友自行填充co2的行為超不安全
何必爲了省那$550元發生意外，後來我打去恆隆行問(客服:0800-251-209)
他們就會到府「交換鋼瓶」，我已經換過2次了(我用的很兇，家裡小朋友每天吵著要喝汽水)
我才知道是不用自己帶著鋼瓶去專櫃打氣的，我還是比較喜歡跟原廠買，不但服務好又安心
大大,自己打氣太危險了啦，我問過朋友自行填充co2的行為超不安全
何必爲了省那$550元發生意外，後來我打去恆隆行問(客服:0800-251-209)
他們就會到府「交換鋼瓶」，我已經換過2次了(我用的很兇，家裡小朋友每天吵著要喝汽水)
我才知道是不用自己帶著鋼瓶去專櫃打氣的，我還是比較喜歡跟原廠買，不但服務好又安心
評分
評分
是已經有把鋼瓶中間壓下去了 還是要手按衝氣時 鋼瓶中心點才會下壓呢
如果是鎖上去時 小鋼瓶中心點就已經壓下去 那就代表
我可以車一個跟鋼瓶頭一模一樣的'公'螺絲(中空) 另外一邊接管
"公" 螺絲 直接鎖上機器
另外一頭接管子 直接接上外面買的大綱瓶
小鋼瓶直接不用
反向思考一下
接下來只要考慮大綱瓶的壓力 是不是要透過壓器閥 再出來才不會壓力過大
評分
小仲 wrote:
.有誰知道 小鋼瓶鎖在機器上面的時候
是已經有把鋼瓶中間壓下去了 還是要手按衝氣時 鋼瓶中心點才會下壓呢
如果是鎖上去時 小鋼瓶中心點就已經壓下去 那就代表
我可以車一個跟鋼瓶頭一模一樣的'公'螺絲(中空) 另外一邊接管
"公" 螺絲 直接鎖上機器
另外一頭接管子 直接接上外面買的大綱瓶
..(恕刪)
恩,這個問題要已經有買sodastream的機器, 而且具有專業知識, 還很閑特別去試試看的人, 才會知道答案吧
你去車一個中空公螺絲,也是要花錢吧. 我觀察了一下sodastream的氣瓶, 覺得好像可以把它的頭給拆了
就是你先買一個灌飽氣的氣瓶, 把裡面的co2用完後, 把銅質的氣瓶頭從鋁罐上拆下來.(大概要用暴力),這樣不就有了一個中空的公螺絲? 只要後面再想辦法能接管就好了
評分
評分
評分
crab69 wrote:
恩,這個問題要已經有...(恕刪)
買一個灌飽氣的大鋼瓶.不用洩氣....當然你也不能只望它能放進主機裡
把原鋼瓶頭拆了裝主機上(不是原鋼瓶頭是無法裝上去的.除非再改)
鋼瓶頭下面車連接頭.連接高壓管.在接減壓.再大鋼瓶
大綱瓶的壓力會壓力過大所以減壓是必須的
評分
http://jmillerid.com/wordpress/2010/03/home-carbonation/
home carbonation
Monday, 15 March 2010
I love seltzer, but I don’t love spending money on bottled seltzer and carrying 50lbs of it home at a time. I recently bought a CO2 tank and regulator for the keg at Crushtoberfest, and I’ve been looking for other uses for it ever since.
It turns out that making seltzer at home is very easy, and once you have the basic equipment the cost-per-bottle is extremely low. Here’s how I set it up:
home-made seltzer
The tank and regulator kit are from Micromatic. The rest is just a handful of fittings from McMaster-Carr, screwed into a hole drilled into a seltzer bottle cap. Here’s the parts list:
part #
quantity
part source
cost
1 1 5lb. aluminum CO2 tank, empty
Micromatic
$59.95*
2 1 tank filling
local welding supply store
about $10-15
3
1 double gauge CO2 primary regulator
Micromatic
$59.95**
4
3′ red vinyl gas hose – 5/16″ ID
Micromatic
$5.55
5
2 hose clamps (pack of 10) – part #5388K14 McMaster-Carr
$5.28***
6 1 Brass Barbed Hose Fitting Adapter for 3/8″ Hose ID X 1/8″ NPTF Female Pipe (pack of 10) – part #5346K34 McMaster-Carr
$18.95***
7
1 Lincoln-Shape Hose Coupling Plug, 1/8″ NPT Male, 1/4 Coupling Size – part #91455K51 McMaster-Carr
$2.78
8
1 Lincoln-Shape Hose Coupling Socket, 1/8″ NPT Male, 1/4 Coupling Size – part #91455K52 McMaster-Carr
$8.38
9 1 Electric Panel Hex Nut 18-8 Stainless Steel, 1/8″-27 Nps – part #91862A306 McMaster-Carr
$3.11
10
1 bottle cap
your recycling bin
$0
11
several empty one, two, or three liter bottles
” ”
$0
TOTAL
$178.95
* you may need to turn this in for a full tank, although some places will fill your tank while you wait
** I bought a good one, you can get these cheaper
*** unfortunately you sometimes have to buy 10 packs (or more) from McMaster. You can get individual hose clamps from your local hardware store.
Here’s how it goes together:
I drilled a hole in the cap (#10) that was just big enough for the threaded end of the coupling socket (#8) and assembled them together with the nut (#9). I used teflon tape in between parts 6 and 7. I also use my CO2 bottle for a keg when necessary, so I got a second set of part 6 and 8 and attached it to the hose coming from the keg tap. This way I can connect and disconnect from one system to the other.
One thing I learned, and this is VERY IMPORTANT: Apparently there is a chemical reaction between the CO2 dissolved in water and copper (or copper alloys like brass) that creates a toxic substance that will make you sick. Never use brass or other copper-based fittings with seltzer! All of these fittings (or at least the ones that will be in contact with the seltzer for any length of time) are either zinc-plated steel or stainless.
The carbonating process is simple. Fill an empty bottle with the liquid of your choice and refrigerate it. Replace the cap with the special one you made and attach the quick-disconnect hose to it. Make sure the shutoff valve on the regulator is closed, then slowly open the main valve on the tank until the regulator shows pressure. Adjust the output pressure to about 45psi and open the shutoff valve, pressurizing the bottle. Now loosen the cap on the bottle just slightly while squeezing any air space out of the neck of the bottle, then tighten the cap. This will purge any air from the bottle and replace it with CO2. Now shake the bottle vigorously for about 20-30 seconds; this will help dissolve the CO2 into the liquid faster. Shut off the CO2 at the regulator and disconnect the hose from the quick-disconnect fitting. You can now remove the special cap (slowly, the contents are now carbonated!) and replace it with a regular cap.
So on the first day I made seltzer water. On the second day I carbonated apple juice, grape juice, and Gatorade, and ended the evening with a carbonated vodka martini (nice!). What else can I carbonate?
======================
將英文翻譯為中文(繁體)顯示拼音
我鑽了一個洞在第（＃10）這僅僅是足夠大的螺紋端耦合插座（＃8）及組裝在一起的螺母（＃9）。我用聚四氟乙烯帶之間的部分6和7。我還用我的二氧化碳瓶一小桶，如有需要，我得到了第二盤的第6和第8和軟管連接到來自水龍頭的桶。這樣我可以連接和斷開從一個系統到另一個。
有一件事情我了解，這是非常重要：顯然是有化學反應之間的二氧化碳溶解於水和銅（或銅合金如黃銅），創建一種有毒物質，會使你生病。切勿使用黃銅或其他銅為基礎的裝置與塞爾策！所有這些配件（或至少是那些將在接觸的塞爾策的任何長度的時間）或鍍鋅鋼或不銹鋼。
在碳化過程很簡單。填寫一個空瓶子的液體和冷藏您選擇它。替換第一個與你所作的特別和附加的快速斷開軟管它。確保切斷閥的調節器關閉，然後慢慢打開主閥上的坦克，直到調節顯示的壓力。調整輸出壓力約 45psi和關斷閥打開，壓瓶。現在鬆開瓶蓋的瓶子，而只是稍微擠任何空出了瓶子的頸部，然後擰緊瓶蓋。這將清除任何空氣從瓶子，取代它的二氧化碳。現在大力搖晃瓶子約 20-30秒，這將幫助溶解二氧化碳轉化為液體更快。關閉二氧化碳在調節和斷開的軟管從快速斷開接頭。現在，您可以刪除特殊帽（緩慢，內容已成為碳酸！），將它與普通的上限。
因此，在第一天我在蘇打水。第二天我碳酸蘋果汁，葡萄汁和佳得樂，結束了晚上，一碳酸伏特加馬天尼（太好了！）。我還可以碳酸鹽？
============================
PSI英文全稱為Pounds per square inch。P是磅pound，S是平方square，I是英寸inch。把所有的單位换成公製單位就可以算出：1bar≈14.5psi
1psi=6.895kPa=0.06895bar 歐美等國家習慣使用psi作單位
============================
剛剛又找到一些瓶閥的網站
http://jia-nan.com.tw/products_08.htm
有誰知道 這類的接頭配件 要去哪一種商店買呢?
評分
內文搜尋