小弟手上有買一台2手的cisco1900不過需要竟然需要密碼!!
不知道各方高手有沒有辦法破解或是消去密碼並從新設定的好方法?
懇請賜教!!
Cisco Catalyst 1900
Firmware version: 3.02
Step-by-Step Procedure
Catalyst 1900
This procedure will allow you to recover a lost or forgotten password on the Catalyst 1900 or 2820 Series. If you have forgotten or lost the password for the management console, you can display it, or, depending on the version of the boot firmware you are using, call Cisco Systems to receive the factory-installed password.
Note: This section does not apply to those Catalyst switches that do not have the Mode button in their front panel. To recover the password on those switches (for example, Catalyst 1700, 2100, and 2800), please refer to the Firmware Version 1.09 and Earlier section listed at the end of this document.
Check the boot firmware version number from the Diagnostic Console - Systems Engineering menu. To access the Systems Engineering menu, follow the procedure below:
Disconnect the power cord from the rear panel.
Press and hold the LED Mode button on the front panel.
While holding the LED Mode button, reconnect the power cord.
Release the LED Mode button one or two seconds after the LED above port 1x goes off. You will see the Diagnostic Console Logon screen as shown below:
-------------------------------------------------
Cisco Systems Diagnostic Console
Copyright(c) Cisco Systems, Inc. 1999
All rights reserved.
Ethernet Address: 00-E0-1E-7E-B4-40
-------------------------------------------------
Press Enter to continue.
Press Enter to display the Diagnostic Console - Systems Engineering menu.
You will see the following Systems Engineering menu:
Diagnostic Console - Systems Engineering
Operation firmware version: 8.00.00 Status: valid
Boot firmware version: 3.02
[C] Continue with standard system start up
[U] Upgrade operation firmware (XMODEM)
[S] System Debug Interface
Enter Selection:The bold letters above show the Boot firmware version. In the example shown above, it is 3.02.
Firmware Version 1.10 and Later
Note: If the shipping date is before June 1997, please refer to the Firmware Version 1.09 and Earlier section of this document, and contact the Cisco Technical Assistance Center (TAC) for password recovery.
Clearing the Password
To clear your password, follow the steps below:
Power-cycle the switch.
After POST completes, the following prompt displays:
Do you wish to clear the passwords? [Y]es or [N]o:
Note: You have ten seconds to respond. If you don't respond within that time, the Management Console Logon screen is automatically displayed. You cannot change this waiting period.
Enter [Y]es to delete the existing password from Nonvolatile RAM (NVRAM).
Note: If you type [N]o, the existing password remains valid.
Assign a password from the switch management interfaces (management console or Command Line Interface (CLI)).
Viewing the Password
For firmware versions between 1.10 and 3.02, you can view the password you are trying to recover (instead of clearing it as described in the previous section).
Access the Diagnostic Console - Systems Engineering menu using the same procedure shown earlier
Disconnect the power cord from the rear panel.
Press and hold the LED Mode button.
While holding the LED Mode button, reconnect the power cord.
Release the LED Mode button one or two seconds after the LED above port 1x goes off.
You will see the following logon screen:
-------------------------------------------------
Cisco Systems Diagnostic Console
Copyright(c) Cisco Systems, Inc. 1999
All rights reserved.
Ethernet Address: 00-E0-1E-7E-B4-40
-------------------------------------------------
Press Enter to continue.Press Enter to display the Diagnostic Console - Systems Engineering menu. You will see the following Systems Engineering menu:
Diagnostic Console - Systems Engineering
Operation firmware version: 8.00.00 Status: valid
Boot firmware version: 3.02
[C] Continue with standard system start up
[U] Upgrade operation firmware (XMODEM)
[S] System Debug Interface
Enter Selection:Select [S] from the Diagnostic Console - Systems Engineering menu to display the System Debug Interface Menu. You can use this menu to display the factory-installed management console password and to reset the management console RS-232 interface or the entire switch to the factory defaults
Diagnostic Console - System Debug Interface
[G] Generic I/O
[M] Memory (CPU) I/O
[F] Return system to factory defaults
[R] Reset main console RS232 interface to 9600,8,1,N
[V] View Management Console password
[X] Exit to Previous Menu
Enter Selection:Select [V] from the Diagnostic Console - System Debug Interface menu to display the management console password. The password will be displayed as shown below:
The current management console password is: CISCO
Now you can use the option [X] to return to the Diagnostic Console - Systems Engineering menu, and then use [C] to continue with the standard system startup which will take you to the User Interface menu. If you want to change the password, select the [M] (Modify password) option on the Console Settings menu. The system will ask you to enter the old password, and then the new password.
Firmware Version 1.09 and Earlier
Note: If the shipping date is before June 1997, please gather the information listed in this section, and contact the Cisco Technical Assistance Center (TAC) for password recovery.
Note: This section is also applicable for those Catalyst 2800 switches that do not have the Mode button in their front panel.
To recover your password, follow the steps below:
Contact the Cisco TAC for the factory-installed password. For security reasons, the factory-installed passwords are not made available on the Cisco web site.
Provide the serial number and/or Media Access Control (MAC) address of the switch.
The serial number is usually located on the back of the unit. To obtain the MAC address, remove the cover and read the Ethernet address of the Programmable Read-Only Memory (PROM).
您可以參考這個網頁,照著做就好了.
http://www.cisco.com/en/US/products/hw/switches/ps574/products_password_recovery09186a00800a6c79.shtml
網路即生活,生活即網路.
內文搜尋
從 APP 打開
X