sin777 wrote:
n16的話，我記得我...(恕刪)
我是因為實在不想用那個還原模式刷 (不想去碰機器)...
所以從 DD-WRT 刷的話刷完直接用 DD-WRT 的 usr/pwd 登入重置即可?
bestpika wrote:
另外我想問一下，To...(恕刪)
抱歉我手中已經沒有N16了，目前手中只有n66U跟R7000
n16我以前也沒有注意刷了tomato後，是不是wps鍵變reset鍵
記得以前用還原程式時，還是用reset鍵壓著沒錯，剛看了easytomato站，發現真的是要你最後按wps鈕來重置，如果你刷了easytomato，就照他做吧
All version:
- openssl update to 1.0.1h
- grow up 6rd-prefix range
- transmission update to 2.83
- dnscrypt: add user selectable/manual proxy input – thx lancethepants
- fix advanced dns/dhcp page
- dnscrypt-proxy update to 1.4.0
- dnsmasq update to 2.71
K26ARM only
- openssl – add options: version, speed and s_client
- add DNSSEC to VPN and AIO builds
ulimie wrote:
[RELEASE] ...(恕刪)
謝謝提醒，目前已刷入v120 ARM-AIO版，還在測試，首測是CTF 開啟，ping 192.168.1.1值會變高，目前在多測幾次試試。
CTF OFF的話，並沒有此情況
--
清除nvram幾次後，CTF 開啟，ping正常了
新增shibby測的wan-->lan 各熱門品牌分享器效能，原文如下
shibby20
Maximum Wan->Lan throughput:
RT-N16 without bcm_nat ~100-120Mbps
RT-N16 with bcm_nat ~ 170Mbps
RT-N66u/AC66u without bcm_nat ~240Mbps
RT-N66u/AC66u with bcm_nat ~320Mbps
RT-N18u/AC56u/AC68u without CTF ~330Mbps
RT-N18u/AC56u/AC68u with CTF ~600Mbps
R7000 without CTF ~410Mbps
R7000 with CTF ~950Mbps
but if you load CPU by any others services then throughput will be much lower. USB support is the most
aggravating CPU service. And it`s not samba/ftp/torrest only. Also if you have syslog/bw monitor/etc stored in USB device, then it also load CPU
以中華電信最快的300/100Mbps速率來看，目前買台n18U就夠用了，如果以300/100或者未來更高速率的寬頻來看，n16/n66u/ac66u是時代的眼淚，不過以現有100/100M都還沒有全台普及來看，這三台還是目前的主流機種。
All version:
- add web module for ip6tables (fixed problem with access restriction)
- libcurl update to 7.37
- transmission upgrade to 2.84
K26RT-N and/or K26RT-AC
- fix VLAN order for RT-N66U – thx @tvlz
- fix VLAN/VID mapping
- fix support of Tenda N60 – please read INSTALATION-N60.txt first!
K26-ARM
- fix 3G modem support for ARM
- add RT-N18U suport
- ET driver upgrade – may fix high ping issue
- fix QoS for ARM
- fix Webmon for ARM
- add GRO CONTROL (should stabilize and speed-up dl/ul speed from Samba) – thx RMerlin
內文搜尋
從 APP 打開
X